NSTL国家科技图书文献中心

1. Experimental Study on the Erosion-Corrosion Synergism of Elbow in the Case of Liquid-Solid Swirling Flow NSTL国家科技图书文献中心

Zhou, Hao | Ma, Hongyan ... - 《Journal of Materials Engineering and Performance》 - 2025,34(2) - 968～986 - 共19页

摘要：The influence of swirling flow on the elbow | erosion-corrosion (E-C) synergism was studied by | experiment and numerical simulation. The numerical values | of four components of E-C rate at different parts | of elbow in the case of liquid-solid swirling flow

关键词： CFD | EDS | elbow | erosion-corrosion | swirling flow | synergism

2. Failure Study of Creep and High-Temperature Tensile Tested Tungsten Inert Gas Welded P92 Steel and AISI 304L Steel Dissimilar Weld Joints NSTL国家科技图书文献中心

Dak, Gaurav | Guguloth, Krishna ... - 《Journal of Materials Engineering and Performance》 - 2025,34(1) - 658～685 - 共28页

摘要：The present study explores the creep and high | -temperature tensile performance of the P92/304L dissimilar | weld joint. The gas tungsten arc welding (GTAW | ) technique was used to prepare the dissimilar weld joint | between P92 creep strength enhanced ferritic (CSEF

关键词： 304L steel | P92 steel | creep | failure mechanism | high-temperature tensile strength

3. Effect of B on Shape Memory Properties and Microstructure of Fe14Mn6Si9Cr5Ni Alloy and Its Mechanism NSTL国家科技图书文献中心

Zhang, Qin | Wang, Hongyu ... - 《Journal of Materials Engineering and Performance》 - 2025,34(2) - 1207～1214 - 共8页 - 被引量：2

摘要：The shape memory performance of the Fe-Mn-Si | shape memory alloy is not satisfactory due to | irreversible plastic deformation during the martensitic | transformation process. In this paper, Fe14Mn6Si9Cr5Ni alloys | with different B additions were prepared by arc

关键词： additive manufacturing | Fe-based memory alloy | materials by design | shape memory materials

4. Thermodynamic and Surface Properties of Liquid Al-Cu-Ni Alloys NSTL国家科技图书文献中心

A.,Dhungana | S. K.,Yadav ... - 《Journal of Materials Engineering and Performance》 - 2025,34(1) - 368～378 - 共11页

摘要：Using the available experimental and | literature data, the linear temperature-dependent | interaction parameters of liquid binary alloys, subsystems | of the Al-Cu-Ni system in the Redlich–Kister (R–K | ) polynomial form were optimized. The activities of pure

关键词： energetics | liquid alloys | modeling | surface tension | the Al-Cu-Ni | thermodynamics

5. Optimization of Process Parameters of Cyclic Expansion Extrusion Process for Effective Grain Refinement of Al-Mg-Si Alloy NSTL国家科技图书文献中心

Babu, V. | Thangapandian, N.... - 《Journal of Materials Engineering and Performance》 - 2025,34(2) - 1717～1732 - 共16页

摘要：This study deals with the interaction among | the cyclic expansion extrusion (CEE) process | parameters, namely processing temperatures, semi-die angles | , ram speeds (pressing velocities) and lubricant types | on the Al-Mg-Si alloy (AA 6063). The design of

关键词： aluminum alloy | cyclic expansion extrusion | EBSD | mechanical properties | optimization | Taguchi technique

6. Preliminary Investigations about Effects of Aging Method on Microstructure and Tensile Properties of As-Eextruded Mg-Gd-Y-Mn-Based Magnesium Alloys NSTL国家科技图书文献中心

Wei, Haobo | Yang, Mingbo ... - 《Journal of Materials Engineering and Performance》 - 2025,34(1) - 896～904 - 共9页

摘要：The effects of two different aging methods | , two-step, and traditional one-step aging treatment | , on the microstructures and tensile properties of | the Mg-10Gd-5Y-0.6Mn-0.5Ca and Mg-13Gd-4Y-0.6Mn | -0.6Ca extruded alloys are investigated and compared

关键词： heat treatment | magnesium alloys | Mg-Gd-Y-Mn-based alloys | one-step aging treatment | two-step aging treatment

7. Thermal Modeling and Parametric Optimization for Machining of Aluminum (Al-10%SiC micro -SiC nano )-Based Hybrid Composite Using Spark Erosion NSTL国家科技图书文献中心

Arif, Umair | Khan, Imtiaz Ali ... - 《Journal of Materials Engineering and Performance》 - 2025,34(1) - 330～355 - 共26页

摘要：In this study, the authors divided the work | into two parts. The first part involved the | development and validation of a thermal model for electric | discharge machining (EDM) using Ansys software. Three | different values of fraction of heat transferred to

关键词： electric discharge machining | fraction of heat transferred to workpiece | grey relational analysis | hybrid composites | pulse current | pulse-on time | thermal modeling

8. High-Frequency Electromagnetic Properties of Injection Molded Soft Magnetic Composites NSTL国家科技图书文献中心

Zhang, Cong | Feng, Shuangjiu ... - 《Journal of Materials Engineering and Performance》 - 2025,34(1) - 145～150 - 共6页

摘要：Soft magnetic composites mean ferromagnetic | powder coated by an electrical insulation layer, which | is often used for high-power electromagnetic | applications. In this work, toroidal magnetic cores such as | FeSiAl and FeNi were fabricated by injection molding

关键词： composites | injection molding | magnetic testing | magnets | metallic matrix | power loss | soft magnetic composites

9. Machining Parameter Optimization of Wire Electrical Discharge Machining for Ni 50.3 Ti 29.7 Hf 20 Alloy Using TOPSIS and Grey Wolf Optimization Technique NSTL国家科技图书文献中心

Bhaskar, Mahadevuni | Balaji, V.... - 《Journal of Materials Engineering and Performance》 - 2025,34(1) - 699～710 - 共12页

摘要：Ni50.3Ti29.7Hf20 is an alloy with shape memory | characteristics that can withstand high temperatures. It | possesses remarkable strength, hardness, and exceptional | corrosion resistance. SMAs are well-suited for various | applications, including automotive sensors, automobiles

关键词： Grey wolf optimization | Ni-Ti-Hf | shape memory alloy | TOPSIS | WEDM | XRD

10. Tribological and Mechanical Behavior of Brake Composite with ANN and TOPSIS NSTL国家科技图书文献中心

Konada, Naresh Kumar | Oktem, Hasan ... - 《Journal of Materials Engineering and Performance》 - 2025,34(2) - 1483～1500 - 共18页

摘要：The demands in the present automotive industry | need an effective braking mechanism for controlling | the vehicle at varying speeds and pressures. In this | study, bronze fiber-reinforced brake pads were | developed for sustaining fluctuating and thermal loads

摘要：The influence of swirling flow on the elbow | erosion-corrosion (E-C) synergism was studied by | experiment and numerical simulation. The numerical values | of four components of E-C rate at different parts | of elbow in the case of liquid-solid swirling flow

关键词： CFD | EDS | elbow | erosion-corrosion | swirling flow | synergism

摘要：The present study explores the creep and high | -temperature tensile performance of the P92/304L dissimilar | weld joint. The gas tungsten arc welding (GTAW | ) technique was used to prepare the dissimilar weld joint | between P92 creep strength enhanced ferritic (CSEF

关键词： 304L steel | P92 steel | creep | failure mechanism | high-temperature tensile strength

摘要：The shape memory performance of the Fe-Mn-Si | shape memory alloy is not satisfactory due to | irreversible plastic deformation during the martensitic | transformation process. In this paper, Fe14Mn6Si9Cr5Ni alloys | with different B additions were prepared by arc

关键词： additive manufacturing | Fe-based memory alloy | materials by design | shape memory materials

摘要：Using the available experimental and | literature data, the linear temperature-dependent | interaction parameters of liquid binary alloys, subsystems | of the Al-Cu-Ni system in the Redlich–Kister (R–K | ) polynomial form were optimized. The activities of pure

关键词： energetics | liquid alloys | modeling | surface tension | the Al-Cu-Ni | thermodynamics

摘要：This study deals with the interaction among | the cyclic expansion extrusion (CEE) process | parameters, namely processing temperatures, semi-die angles | , ram speeds (pressing velocities) and lubricant types | on the Al-Mg-Si alloy (AA 6063). The design of

关键词： aluminum alloy | cyclic expansion extrusion | EBSD | mechanical properties | optimization | Taguchi technique

摘要：The effects of two different aging methods | , two-step, and traditional one-step aging treatment | , on the microstructures and tensile properties of | the Mg-10Gd-5Y-0.6Mn-0.5Ca and Mg-13Gd-4Y-0.6Mn | -0.6Ca extruded alloys are investigated and compared

关键词： heat treatment | magnesium alloys | Mg-Gd-Y-Mn-based alloys | one-step aging treatment | two-step aging treatment

摘要：In this study, the authors divided the work | into two parts. The first part involved the | development and validation of a thermal model for electric | discharge machining (EDM) using Ansys software. Three | different values of fraction of heat transferred to

关键词： electric discharge machining | fraction of heat transferred to workpiece | grey relational analysis | hybrid composites | pulse current | pulse-on time | thermal modeling

摘要：Soft magnetic composites mean ferromagnetic | powder coated by an electrical insulation layer, which | is often used for high-power electromagnetic | applications. In this work, toroidal magnetic cores such as | FeSiAl and FeNi were fabricated by injection molding

关键词： composites | injection molding | magnetic testing | magnets | metallic matrix | power loss | soft magnetic composites

摘要：Ni50.3Ti29.7Hf20 is an alloy with shape memory | characteristics that can withstand high temperatures. It | possesses remarkable strength, hardness, and exceptional | corrosion resistance. SMAs are well-suited for various | applications, including automotive sensors, automobiles

关键词： Grey wolf optimization | Ni-Ti-Hf | shape memory alloy | TOPSIS | WEDM | XRD

摘要：The demands in the present automotive industry | need an effective braking mechanism for controlling | the vehicle at varying speeds and pressures. In this | study, bronze fiber-reinforced brake pads were | developed for sustaining fluctuating and thermal loads

关键词： bronze fiber | coefficient of friction | prediction methods (ANN, TOPSIS) | wear rate

4008-161-200 800-990-8900

国家科技图书文献中心